|Material:||Stainless Steel 304||Application:||Industrial Ultrasonic Cleaner|
|Tank Capacity:||1500L||Industry:||Turbo Blade / Aerospace Component|
|Option 2:||Oil Filtration||Frequency:||28khz|
industrial ultrasonic parts cleaner,
automotive parts cleaning equipment,
1500L Aerospace Component Ultrasonic Cleaner
1500L Oil Filtration Industrial Ultrasonic Cleaner , Turbo Blade / Aerospace Component Ultrasonic Cleaner
Larger ultrasonic tanks usually feature heavier duty wall construction and additional wall support. Heat may be supplied in a variety of ways including electric immersion heaters, steam coils, and/or external heat exchangers. Larger tanks may have either diaphragm-bonded transducers, or immersibles which are transducers bonded into a stainless steel can which is then mounted in the cleaning tank. The advantages of immersibles are that a can may be swapped out if required without the whole tank going down, and immersibles can often be retrofitted into existing process tanks to improve cleaning performance.
Automotive Ultrasonic Cleaner by Cavitation Action
Get exactly what you need.
ultrasonic units to choose from. Units can be customized and retrofit by the AGSONIC team, like the units Eaton Aerospace uses, but an existing model may do just fine. Every unit offers our clients the same benefits.
Ultrasonic cleaning equipment for use in Aerospace
•High-quality, precision results with even intricate pieces or uniquely shaped or sized parts
•Lower labor costs and increased production efficiency
•Easy to use and setup; no training required
•Reduces the use of toxic solvents and expensive waste removal services
•Uses only EPA-approved water-based solutions
Ultrasonic cleaning technology reaches the most inaccessible surface areas of complex aerospace components used in manufacturing, overhaul, servicing and maintenance stages. ultrasonic equipment provides a much faster and higher quality cleaning results than spray washing and manual scrubbing. It is a more environmentally friendly alternative to solvent cleaning.
All ultrasonic baths are supplied complete with lid and basket
Base Metal Aircraft Accessories Aviation Indutrial Ultrasonic Cleaner For Steel Aluminum Copper Brass Magnesium
The process is fairly straight forward regardless of equipment size. Here’s a simplified description that can be modified based on your specific operations:
1.Fill the ultrasonic cleaner with water but allow room for cleaning solution displacement due to the size of the molds being cleaned. Add the proper amount of biodegradable cleaning solution concentrate. Ask the scientists at Tovatech to recommend the correct formulation based on the type of contaminants you are removing and what the mold itself is made of.
2.When you are ready to clean place the urbo Blade / Aerospace Component in the cleaner basket. Take care that they do not contact each other. If you are cleaning large parts you may suspend them in the cleaning solution so they do not contact the tank bottom. Some industrial cleaners are equipped with bottom racks to support products being cleaned.
3.Set the heater to 65 C and timer from 10 to 60 minutes depending on the degree of contamination. Activate the sweep mode to assure uniform distribution of cavitation and promote uniform cleaning then lower the molds into the solution. With experience you will establish optimum cleaning conditions.
4.At the end of the cycle remove the urbo Blade / Aerospace Component and inspect. When satisfied, rinse them with fresh hot water and allow them to dry or blow them dry with compressed air. Note that intricate configurations and cavities may trap water that should be removed by adding an electric drying oven to your setup.
Rinsing tip: You’ll want to thoroughly remove cleaning solution residues. Complex shapes may call for a spray rinse or, in certain cases, rinsing by cavitation in an ultrasonic rinse tank.
Saved more than 20 labor hours and minimized employee chemical exposure.
AGSONIC wasn’t the cheapest or the most expensive. They had an excellent product for the money and a commitment to customer service. AGSONIC is very easy to work with, even from 2,000 miles away. The retrofit and all other support needs have been handled in a very responsive manner. AGSONIC ’ dependability and service are part of our operational success. As far as our employees and management are concerned, our AGSONIC units are here to stay. For any future needs, AGSONIC is our 1 choice.
– Customer feedbaack Aerospace.
ultrasonic tank models for your choice:
|Model||Tank size||Unit size||Volume||Ultrasonic power||Frequency||Heating power||Timer||Heating temperature|
Features of the machine:
• Low maintainence machine
• Heavy duty cleaning systems
• Chemical friendly- SS Rust proof body
• Industrial guage farication, build to last
• One year warrenty on any manufacturing defect
• Completely customized to suit the cleaning requirement
• Less human interfearance and less scope of error
• Accurate and uniform cleaning everytime
Contact Person: AGSONIC